Minisforum MS-01 vs GMKtec NucBox G3: Which Should You Buy?
Affiliate disclosure: some links below are affiliate links. If you buy through them we may earn a commission at no extra cost to you. See our full disclosure.
Two mini PCs that could not be more different in intent. The Minisforum MS-01 is a serious virtualization and storage node with real networking. The GMKtec NucBox G3 is a cheap, cheerful N100 box you buy three of without flinching. I’ve run both classes of machine in my own rack, and the buying decision comes down to one question: are you building a lab, or are you building a service?
Quick verdict
| You are… | Buy this |
|---|---|
| Running Proxmox, TrueNAS, or a multi-VM cluster and want 10GbE + PCIe expansion in one box | Minisforum MS-01 |
| Standing up a first homelab, a Pi-hole/DNS box, a lightweight Docker host, or a media front-end on a tight budget | GMKtec NucBox G3 |
| Needing vPro/remote management and lots of RAM headroom | Minisforum MS-01 |
| Wanting the cheapest capable transcoding node you can tuck behind a TV | GMKtec NucBox G3 |
Spec-by-spec
| Spec | Minisforum MS-01 | GMKtec NucBox G3 |
|---|---|---|
| Price | $650 | $170 |
| CPU | Intel Core i9-13900H (14C) | Intel N100 (4C) |
| RAM | up to 96GB DDR5 | up to 16GB DDR4 |
| Network | 2x 10GbE + 2x 2.5GbE | 1x 1GbE |
| Transcoding | Yes (Iris Xe) | Yes (N100 QuickSync) |
| Expansion | PCIe x16 + U.2 + 2x M.2 | single NVMe |
| Best for | Powerful homelab node | Ultra-budget N100 |
The MS-01 is a networking and expansion story first
The headline isn’t the i9-13900H — it’s the four network ports. Two 10GbE plus two 2.5GbE on a single mini PC is the kind of IO that used to require a full ATX build with a PCIe NIC. For anyone running a router/firewall VM, a NAS VM, and a couple of compute VMs on the same physical host, that port count is transformative. Combined with the PCIe x16 slot, the U.2 bay, and dual M.2, the MS-01 is the rare mini PC that can be a storage node as well as a compute node. The 96GB DDR5 ceiling matters too — if you’re carving RAM out to a dozen VMs, headroom is everything.
The honest caveat: it runs warm. A 14-core i9 in a small chassis with that much IO is going to move heat, and you should plan airflow around it rather than stuffing it in a closed cabinet. That’s a real consideration, not a dealbreaker.
The NucBox G3 is the right kind of boring
The N100 is the workhorse of the budget homelab for good reason: it’s efficient, it’s capable, and QuickSync transcoding means it punches far above its price for media work. The G3 gives you a single 1GbE port, a single NVMe slot, and a 16GB DDR4 ceiling. That’s it. Basic IO is the con, and it’s accurate — you are not running a router VM or a multi-disk NAS on this box.
But here’s the thing: for a DNS resolver, a reverse proxy, a Tailscale exit node, or a Jellyfin front-end, a 1GbE port and one NVMe are plenty. The G3’s job is to be cheap enough that you buy a second one as a spare. At $170 it earns that.
Where the price gap actually goes
The $480 difference buys you networking, RAM ceiling, and expansion — not raw CPU alone. If your bottleneck is “I need more 10GbE ports and a place to put a U.2 drive,” the MS-01 is the only one of these two that answers. If your bottleneck is “I need a box that stays up and serves DNS,” the G3 answers it for a quarter of the money. Spend the difference on drives and a backup target instead.
Which brings up the thing nobody says loudly enough: none of this is a backup until a copy lives off-site. I use Backblaze B2 for object storage and IDrive as a second destination. Whichever host you pick, wire up off-site copies before you wire up anything else.
And for remote access, skip the port-forward. Use Tailscale — free, easy, and it gets you in from anywhere without exposing services to the internet. If you want a whole-network mesh rather than per-device, NordVPN Meshnet is a solid alternative.
Pros & cons
Minisforum MS-01
- ✅ 2x 10GbE + 2x 2.5GbE — genuinely rare in a mini PC
- ✅ PCIe x16, U.2, and dual M.2 for real expansion
- ✅ Up to 96GB DDR5 and vPro remote management
- ✅ Iris Xe transcoding
- ❌ Runs warm — plan airflow
- ❌ $650 is real money for a single node
GMKtec NucBox G3
- ✅ Very cheap at $170
- ✅ Capable N100 with QuickSync transcoding
- ✅ Great as a spare or a dedicated service box
- ❌ Basic IO — one 1GbE, one NVMe
- ❌ 16GB DDR4 ceiling limits heavy virtualization
Which should you buy
Buy the MS-01 if you’re consolidating a lab onto one box and want the networking and expansion to grow with it — and you can live with managing its thermals. Buy the NucBox G3 if you’re starting out, want a cheap always-on service node, or need a transcoding box without spending real money. Honestly? The best homelab often has both: an MS-01 as the heavy compute/storage node and a G3 or two as cheap, resilient service boxes. Protect whatever you build with off-site backups and Tailscale, and you’re done.
FAQ
Is the N100 good enough for a homelab? For DNS, reverse proxying, lightweight Docker, and media transcoding via QuickSync, yes. For heavy multi-VM work or lots of RAM-hungry services, the 16GB DDR4 ceiling will bite.
Do I need 10GbE in a mini PC? Only if you’re moving large datasets between hosts or running storage over the network. For most home service loads, 1GbE is fine — which is exactly why the G3 exists.
Can both of these transcode? Yes. The MS-01 uses Iris Xe; the G3 uses N100 QuickSync
Homelab essentials
Whichever tools you land on here, two things make any self-hosted setup safer:
- Privacy + secure remote access — reach your services from anywhere without exposing ports to the internet. Our pick is NordVPN — independently audited no-logs, fast, with Meshnet built in for linking your devices.
- Off-site backup for your configs & data — pCloud, EU/Swiss-based with optional zero-knowledge encryption and one-time lifetime plans, so a dead drive never costs you your setup.